Как соединить роликовую цепь: соединительные звенья или штифты с запрессовкой.

How the Drive System Works

A roller chain transmits mechanical power by engaging sprocket teeth through its rollers, which rotate freely on bushings. The chain itself is a series of alternating inner and outer link plates joined by pins. The inner plates house hardened steel bushings; the outer (or pin) plates are pressed onto the pin ends. When the chain wraps around a driving sprocket, each roller seats cleanly into the sprocket valley, reducing contact wear while transferring torque efficiently. The chain’s connection point — where the two open ends of the chain are joined to form a closed loop — must reproduce the same mechanical integrity as every other link in the assembly. Any compromise at the joint means that link becomes the weakest point, and under cyclic loading it is almost always the first to fail. This is why both the master link and the press-fit pin method are engineered to specific tensile and fatigue ratings, not simply bolted together as an afterthought.

Load Distribution at the Link

When tension is applied to a roller chain, the load travels through the link plates in shear and through the pins in bending and bearing. At the connection point, the load path must be continuous and uninterrupted. A master link achieves this through a slip-fit outer link plate that is retained by a spring clip — meaning the pin-to-plate interface is slightly looser than a standard press fit. A press-fit riveted pin, by contrast, uses the same interference-fit construction as every other link in the chain, so the load path characteristics are identical throughout the loop. This distinction has meaningful implications for fatigue life, particularly in applications running above 200 RPM or carrying shock loads — conditions common in the steel processing corridors of Sheffield and the mining-adjacent industries of the North East.

Fast Installation

No press tools or riveting equipment required. Clip engagement takes seconds once the link is seated, making it practical during planned maintenance windows with limited downtime budgets.

Reusable (With Caution)

The connecting link body can be reused if undamaged; only the spring clip should be renewed at each removal. Always replace the clip — a fatigued or distorted clip is a silent failure waiting to happen.

Диапазон шага

Reliable from 1/4 inch (6.35 mm) up to approximately 1-1/2 inch (38.1 mm) pitch. Beyond this range, the clip retention force becomes marginal relative to working load, and riveted options are strongly preferred.

The press-fit (or peened/riveted) pin connection is the approach used during original chain manufacture and represents the highest-integrity method for permanently closing a roller chain loop. Rather than a sliding plate retained by a clip, the outer connecting plate is pressed onto the pin ends using an interference fit — the same construction method used at every other link in the chain. Once in position, the protruding pin ends are peened outward using a chain-riveting tool or hydraulic press, physically deforming the metal to lock the plate permanently in place. This creates a joint whose tensile strength is indistinguishable from the rest of the chain, with no additional mechanical weakness at the closure point.

The press-fit method is mandatory in several classes of application. Roller chain used in overhead lifting conveyors, safety-critical drive systems, and any roller chain configuration carrying human-safety implications — such as rides at leisure parks or guided transport systems — must be closed with a riveted pin connection. British standards governing lifting equipment and safety-critical machinery explicitly prohibit the use of spring clip master links in these scenarios. Similarly, large-pitch roller chains (above 1-1/2 inch / 38.1 mm) and multiple-strand chains used in heavy mining or quarrying equipment — including plants operating in the Midlands quarry belt — are consistently specified with riveted closures because the dynamic loads involved would place the clip under repeated stress cycles well beyond its reliable operating range.

Full Tensile Integrity

Joint strength matches the chain rating — no derating required. Essential for high-load applications above 85% of MBF.

Fatigue Resistance

No clip to vibrate loose. Ideal for high-cycle, high-speed, or shock-loaded drives running continuously in industrial settings.

Permanent Assembly

Not intended for repeated disassembly — chain must be broken with a pin-extractor tool for removal, meaning length adjustments require cutting.

Tooling Required

Requires a riveting press or peening hammer set matched to the chain pitch. Improper peening leads to cracked plates — always use calibrated tooling.

Assembly line conveyors in the automotive clusters around Coventry and Birmingham run heavy roller chain continuously for multi-shift operations. These drives carry body panels and sub-assemblies across process stages at controlled speeds, but the chain is never idle for long enough to tolerate connection point failures. Press-fit riveted pins are standard here — the lines cannot afford the inspection intervals that a clip link would demand, and any joint failure at this scale triggers a line stoppage costing thousands of pounds per hour. The roller chain specification is typically heavy-duty BS ISO 10B-2 or 16B-2 in twin-strand configuration, with riveted closures as standard from the OEM supplier.

Food-grade roller chain in biscuit, confectionery, and ready-meal production facilities across Yorkshire must meet strict hygiene standards under UK Food Standards Agency regulations, but it must also be field-serviceable by maintenance teams during short washdown windows. Here the master link — preferably in stainless steel or nickel-plated carbon steel to resist cleaning chemicals — is the pragmatic choice. Maintenance teams can replace a worn section of chain or re-close an opened run in minutes without bringing in a hydraulic press. The working loads in food conveyors are moderate; the real challenge is corrosion and chemical resistance rather than raw tensile load, which keeps clip links within their safe operating margin.

Sheffield’s special steel and stainless steel processing industry still runs extensive roller chain on furnace-transfer conveyors, bar-rolling lines, and coil-handling systems. The temperatures, loads, and shock characteristics of these environments make the press-fit riveted pin the only viable connection method. Chains in furnace transfer applications often require heat-resistant pin coatings and hardened link plates specified to BS EN 10083 material grades — and the closure joint must meet exactly the same material specification. Custom-length chain with riveted closures is the standard procurement format for this sector.

Combine harvesters, balers, and grain dryers across the Lincolnshire and Norfolk flatlands run multiple roller chain drives simultaneously during the harvest window. Agricultural roller chain is typically ANSI/BS double-pitch in longer run lengths, and the connection method reflects the field-service reality: clip links dominate because repairs must happen in the field, with limited tooling, under time pressure during a harvest that may only last a few days at optimal grain moisture. Farmers and agricultural contractors in this region stock a variety of master link sizes — commonly 40, 50, and 60 ANSI pitch — as an essential part of their field service kit. The 20B-G1 Резиновая роликовая цепь from Ever Power is used in grain handling elevator legs where the rubber top reduces grain damage during transfer.

Carbon Steel (Case-Hardened)

The most common base material across standard BS/ISO and ANSI roller chains. Pins are carburised to a surface hardness of HRC 58–62 while maintaining a tough core, giving them resistance to both surface wear and shock bending. Link plates are stamped from strip steel to a specified ultimate tensile strength, typically 700–900 MPa for standard grade.

Stainless Steel (304 / 316)

Grade 316 is preferred wherever chloride exposure is possible — coastal processing facilities in the South West of England, marine-adjacent industries, and any application using aggressive cleaning agents. Master link clips in stainless are typically 316 as well. Note that stainless chain carries lower tensile ratings than an equivalent carbon steel grade, so working load calculations must be redone when upgrading to stainless.

Nickel-Plated Carbon Steel

A cost-effective middle ground between plain carbon and full stainless. The electroplated nickel layer provides a degree of corrosion resistance suitable for mild wet or washdown environments without the cost premium of solid stainless construction. Widely specified by UK food manufacturers who need HACCP-compatible chain with the tensile performance of carbon steel.

Spring Steel (Clip Material)

The retaining clip on a master link is stamped from high-carbon spring steel, heat-treated to provide the elastic retention force that keeps the clip locked in the pin groove. A clip that has been over-flexed, corroded, or left in service beyond its rated cycle count will lose spring force and can disengage — which is why visual inspection of the clip at every maintenance visit is non-negotiable.

Ever Power operates a fully integrated roller chain manufacturing facility producing standard and custom chain solutions for clients across the UK and global markets. Our precision manufacturing process covers every stage in-house — from raw steel strip procurement through to cold-drawing, heat treatment, plate stamping, pin turning, assembly, and final tension testing. This end-to-end control means that when you specify a custom pitch, custom plate thickness, special surface treatment, or a non-standard connecting link configuration, we can engineer and certify the complete solution without relying on third-party sub-suppliers who might introduce dimensional inconsistencies.

Our customisation capabilities span a wide range: special pitch roller chain outside standard BS/ISO ranges, extended-pin chains for cross-member attachment, hollow-pin chains for easy lateral attachment, extended-plate chains for guide rail integration, and surface treatments including case hardening, shot peening, zinc plating, and food-grade lubricant pre-application. We also manufacture replacement master link sets and press-fit connecting link kits as standalone supply items — useful for UK maintenance teams who need to keep a comprehensive spares kit to BS/ISO specifications without sourcing each component separately from different distributors.

Lead times for standard roller chain products to UK warehouse stock are typically 15–25 working days by sea freight, with express air freight options available for urgent breakdown replacement. Our supply chain team coordinates all export documentation, UKCA compliance statements, and materials certification (EN 10204 3.1) to meet the requirements of quality-managed purchasing teams across British manufacturing.

📧 Request a Custom Quote

Meridian Alloys operates a bar stock cutting and finishing line in Sheffield’s industrial east end, processing high-alloy steel rounds for the aerospace and tooling supply chain. Their bar-transfer conveyor system runs on a set of 16B-2 twin-strand roller chain drives across twelve chain runs, covering approximately 85 metres of total chain length. Prior to engaging Ever Power as their chain supplier, the maintenance team was sourcing chain from two different UK distributors who each stocked a slightly different tolerance specification — causing interoperability problems when replacing individual chain sections, and leading to premature wear at connection points where the sections met.

The facility’s engineering manager contacted Ever Power after seeing the company’s technical specification documentation online. The challenge was straightforward: supply 16B-2 chain to a single, tightly controlled tolerance across all twelve runs, with riveted press-fit closures on every loop, accompanied by EN 10204 3.1 mill certificates on the base steel. All twelve runs needed to be the same length within ±0.05% to prevent differential elongation between parallel drives. Ever Power’s technical team reviewed the existing chain layout drawings, confirmed the correct pitch count for each run, and supplied the full batch — 12 custom-length closed loops — within 22 working days of order confirmation. Each loop was pre-assembled with press-fit riveted connecting links and arrived with individual batch certificates.

Within six months of installation, the Meridian Alloys maintenance team reported zero chain-related stoppages — a marked contrast to the 3–4 unplanned stoppages per quarter they had experienced with the mixed-source chain. The uniform specification across all twelve drives allowed the maintenance team to implement a consolidated replacement schedule rather than reacting to individual run failures, reducing their spare parts inventory and simplifying procurement. Ever Power continues to supply Meridian Alloys on an annual renewal schedule, with updated EN 3.1 certification accompanying every batch.

“The riveted press-fit closing links that came with our 16B-2 batch were exactly what we needed — same tolerance as the chain body, fully certified, and the peening was clean and consistent on every single one. We have not had a single joint failure across six months of continuous three-shift operation. That speaks for itself.”

D. Hartley — Engineering Manager, Sheffield Steel Processing

“We specified nickel-plated master link sets from Ever Power for our food-grade conveyor upgrades across the West Yorkshire site. The clips arrived pre-packed by pitch size and were accompanied by a clear installation torque guide. Our maintenance team got through the entire conveyor changeover in one planned shutdown window without any rework. Supplier communication was excellent throughout.”

S. Patel — Maintenance Supervisor, Ready Meal Production, Leeds

“We switched to custom-length closed loops from Ever Power for our quarry conveyor upgrade in Derbyshire. The tight tolerance on length across all eight drives has eliminated the uneven chain elongation we were seeing with our previous supplier’s product. The press-fit closures have been in service for eight months now across a very demanding application and there are no signs of fatigue cracking or clip issues — because there are no clips to worry about.”

T. Birch — Plant Engineering Lead, Aggregate Processing, Derbyshire